[F777]IKB4

It's amazing that scenarios from IKB3 works on IKB4 too (but not all). I think the scenarios that go beyond Bad Rinckenstadt may be broken due to the addition of the SFS tunnel, but I haven't tested them yet

Niederkirch ready. Until I hang the section dividers (streckentrenner) on the wire, I need to go to Altenburg and replace the entire wire there, and then move from Koblenz to Bad Rinckenstadt.

I don't know about you all, but I really like the result. The only nuance is the tension masts with wires for wire holders. I mean this:

In reality, as I understood it, from the topmost wire, which runs in an arc from mast to mast, wires go to the bottom only where the wire holders of the contact network are located. But in the TSC package, everything here is done with a grid. I know that there are tools for manually stretching all these wires, but I already sat with one mast for about 2 days trying to figure out all the subtleties. That's why I decided to simplify my life a lot. I don't know how critical this is for you. If I ever have a wish (after the project is finally released) to change it, I will do it. At the same time, it will be possible to hang isolators more realistically so that they really isolate the wires from each other, and not just the holders themselves.

Breaking the quiet with some fresh news about this project.
I worked hard until the New Year, then I rested, studied the structure of the contact network in my country. Then successfully passed the university session and continued my work. What have I done in that time?
This is how Altenburg HBF looks now. New catenary (oberleitung), new signals, new vegetation and (unexpectedly) brand new bridge. I decided to redo it, as I noticed that bridge was very crookedly made half of loft, half of ordinary assets. Now it has a beautiful concrete base and a noise shield.

In addition, based on my new knowledge, I redesigned the neutral catenary section near Koblitz, and also began adding section separators throughout the network.

In reality, separators are needed so that you can disconnect some of the wires from the power supply and carry out technical work. Of course, the detail of these sections is limited by the capabilities of the TSC contact network package and my time, but I tried to make everything as beautiful and believable as possible.

In addition, I have completely completed the rework of the Koblitz - Bad Rinckenburg branch catenary. It remains to adapt the Hectometers to the new concrete masts. As soon as I finish all this changes with the contact network, I can finally move to the branch to Hoch Merzburg.

I started moving along the branch line to Hoch Merzburg. At the moment, I'm installing asset blocks and changing the settings of existing ones to use 2D RLB vegetation from Konstanz Villingen. In some places, I've already tried adding 3D vegetation and seeing how everything looks in general. At the moment, there are no OHLE changes, if I'm going to do this, then after the complete completion of work on vegetation.

The distant vegetation and grass are ready up to 163 kilometer, where Schwanstetten is located. Previously, the station was located closer to the center of the town, and there were fairly developed industries next to it, but all that remained of it was a small woodworking plant, an abandoned driveway and closed station.

Old and new:

Why one? It's like on Freiburg - Basel route, but with the combination of both SFS paths to reduce the number of switches and make it more compact. There won't be many trains on this line anyway.. Track laying is not ideal, but sorry, it's my first attempt at route building

This is how the entire mountain part from Bad Rinckenburg to Hoch Merzburg will look like

dj bahn and other guys who are always missing some pieces of rails. As I understand, it is missing purely graphically, you can drive on them and they appeared at 2D map, right? If so, then you just kind of have the same broken on unfull copy of EZY package, because I use [EZY] Gleis oS Holz1Alt bl variant in the Hosvenn bridge, for example
Installed clean copy of route and here it is:

This example from the great KBS172 scenario, all right and working

Zitat von Trainmaster001

Hello Forza Gamer 777 ,

I´ve the error with the Tracks. Yes, I can drive on them and they are at the 2D Map. Which Route shoud I reinstall?

If you can drive on them, it means that you do not have the graphical component of the rails, it is necessary to reinstall the EZY package.