Beiträge von Forza Gamer 777

Koeblitz. FUZ and Zp9 indicators from newer Ks signals pack from 143er . Thus, two Ks packages are now used on the route. In one there is an opportunity to make SignalBruecke, in the other there are more options for signals and indicators. The packages complement each other and their overall use looks really interesting. Instead of homogeneous Hv, there will now be Ks in two versions on suburban branches, as well as Hv/k in some places.

Zitat von BR-218

Hier gibt es die besten Formsignale.

Filebase-Eintrag

[RLB] Formsignale DB+DR V9.8

Achtung!
-----------
Das Paket beinhaltet diverse deutsche Formsignale der Deutschen Bundesbahn sowie der Deutschen Reichsbahn.
Es sind Haupt- Vor- und Sperrsignale sowie Wartezeichen und diverse Zusatzsignale enthalten.
Es ist eine Gemeinschaftsarbeit.…

Schuster

12. August 2018

They look a little old in textures, but I'll take a look. First I finish the rest of other sections, Formsignale is a low problem in terms of quantity

I'll write down my progress in a couple of days so that you understand how much has changed. I must say right away that the signaling changes are already likely to go to IKB4, which will in fact be a separate route. But the scenarios should run without problems, since all links to the signals are placed exactly to original.

• All Zp9 at Bad Rinckenburg Hbf and Altenburg Hbf have been replaced with CMD variants, it is possible to control them through triggers
• SFS speed increased to 280 km/h
• Swapped all SFS signalling from Bad Rinckenburg to Altenburg to CMD Ks, now, if LZB is active, the signals are turned off. LZB subblocks now in production, I've postponed them for now, but I'll definitely finish them when IKB4 comes out. There is a problem with the placement distance, it is difficult to place everything accurately, since 70 percent of the SFS goes in tunnels
• Added more Zs3 and Zs2 signals, increased the number of Zs6, added an adequate opportunity to fully use the wrong track paths for scenarios

In the plans:

• Swap the entire suburban line via Koblitz from Hv to Ks
• Change line Koeblitz - Wildau and Bad Rinckenburg - Hoch Merzburg with Hv Kompaktsignale from SBS
• Maybe replace some Formsignale, but don't know, from where I can take best (in quality and visual) signal pack.

Zitat von domi5599

Your question about the block length. What is the signal block length on the sfs?

2-2.5 km

Zitat von domi5599

Wow would be really glad if you get the signals dark with active lzb.

Completed

LZB Blocks working as well, but I don't know proper intervals for it

Zitat von domi5599

Danke fürs Antworten BR-218 wusste gar nicht, dass das im TS schon so geht. Lässt sich damit auch schon ein LZB-Teilblockmodus realisieren?

Yes, here is special CMD Ks Hs LZB 0T signal. Testing it right now

Yes, this section is in the KS system.

I can't figure out yet why the assets of the RoterStein package are not loaded into my editor. I wanted to take the LZB blocks from it. There is no objects with MS prefix

domi5599 I probably translated it a little incorrectly from Russian, I didn't mean the neutral section, but the section with the lowering of the pantograph. Thanks for the information, here on the route, the catenary is made so that it does not physically drop below, so I thought it was a glitch. Plus, I remembered how in TSW the pantograph itself smoothly becomes lower if the catenary goes under the bridge, so I thought that something was wrong with the arrangement of El4 and 5, thanks a lot for your help. Now I need to find out how to place the digital sections of the LZB so that signals of the Ks system are turned off when the LZB is running

Zitat von domi5599

If your section needs only to be driven through without top panto is the following important.

El 3 is the pre signal for El 4 and stands normally half of the braking distance in front of El 4. El 4 must stand min. 30 m before the section and El 5 30 m after the section ends.

This is understandable, the problem here is that both signals, El4 and 5, are behind the section

Or is the section itself located exactly under the bridge? I just can't figure out which of these is the neutral section.

CMD.Cornflakes, you just read my mind. I was just doing VS today, I thought that I was missing some VS plates for SB. Way better now, thank you again

Zitat von CMD.Cornflakes

You don't have to do that, I added the necessary variants to the package today

The error on Zp9/10 has also been fixed.

Just download it again.

Filebase-Eintrag

[CMD] Ks Signale V1.2

Diese Signal Paket enthält sehr detailreich ausmodellierte Ks Signale so wie modular aufbaubare Signalbrücken

Damit die Signale Funktionieren werden die Freeware Skripte von Schuster benötigt!
Hier klicken für die Freeware Skripte

CMD.Cornflakes

27. November 2022

It's just crazy, that's exactly what I needed, thank you so much!

Btw, I have 1 question, but not about KS. Are these El4 and El5 signs standing correctly? They are located after the place where the wires physically intersect, but not exactly in this place

CMD.Cornflakes , if you will, I'll add a couple of custom Zs6's based on your package in 2T and 3T versions to my update. I need them for Altenburg Hbf.

BR-218, I have a problem with Zp9/Zp10 indicator. Zp10 works

But Zp9 shows broken "0" texture.

How I can fix this? Or it's CMD.Cornflakes bug?
Placed near Zp9, here is the difference

Zitat von Marcel Kühne

Forza Gamer 777 - Can you please change the tracks in Köblitz yard from grey to brown? Doesn't look right now.

Greetings, Marcel.

The problem is that there was originally a gray ballast, I just changed the SAD rails to EZY, identical in color, if I change the color of the ballast there, then it is to shift the tracks, or somehow look only for the location of the rail in Tracks.bin, which I do not know how to do

Replacing Ks across the entire SFS

I had to improvise in the tunnel, as there are no necessary fasteners to the wall in the pack, unfortunately

The only thing I did not understand in this constructor is whether it is possible to add the Zs2 indicator here, above the Zs3v

P.s. Figured out

And that's working

But for some reason, the number 6 on the Zs3v does not go out with Hp0, I do not know what my jamb may be.

Zitat von Marcel Kühne

What we now need is a new overheadline and curve superelevation. Than it's perfect.

Liebe Grüße, Marcel.

I agree about the superelevation, but the OHLE, in my opinion, looks great as it is.

Zitat von tom87

I only have "Loft Files", "Road Files" and the "Tracks.bin" in the network folder.... why is there no "Track Files" folder?

If by some miracle my improvement was installed separately from the basics, then transfer all the main files to this folder first, and then my update files. My update contains only the updated files, not the entire route

@tom87 Along the path \Content\Routes\53340446-fc5e-464e-824d-7c4693229611\Networks, you have an old archive Tracks Default.zip? If there is, delete it

Zitat von tom87

I don´t have any track on the route... any solutions for this?

I've dug through everything I could, maybe you have an old version of the EZY rail? They had an update released in July

Damn, I didn't know that it depends on the restart, I thought that it just doesn't work for me. Thanks for this information, I know the rest. That's how it looks now: