RW Enhancer 2 erschienen

I think thats not only a Steamtrain Problem, because Transfer-Points are used for Container Loading too. ( If you want i can create an example) .

You are right, at the moment refueling points are working but not container loading, this should come soon

Zitat von StS

I think thats not only a Steamtrain Problem, because Transfer-Points are used for Container Loading too. ( If you want i can create an example) .

Currently working on implementing freight loading detection support in RW Enhancer 2. This should come as "experimental" (waiting for player feedback) in the next update.

EDIT: New update is ready and under testing. This update will be released tomorrow. Here is the changelog in advance. StS Hopefully it will work nicely for most of your scenarios involving freight loading

- Added new radio message when a freight loading task is completed

- Added 'Pickup Fuel/Freight' tasks arrival and departure time in service sheet if the task is timetabled

- Improved 'Pickup Fuel/Freight' tasks handling

- Fixed tasks locations not using localized names (when available) in the service sheet

- Fixed 'Pickup Fuel/Freight' task not detected correctly if it was assigned to a regular route marker and not a transfer point

- Fixed 'Pickup Freight' task delay calculation when the task is timetabled

- Fixed 'Pickup Freight' task completion detection

oldsnake Your costumer support is outstanding.

oldsnake

Is the Testversion avialable anywhere? Ican do a test too.

Zitat von StS

oldsnake

Is the Testversion avialable anywhere? Ican do a test too.

Please contact me at RWCentral.com by PM

I got a version 14.04_19:47:
No Success:

The task 1 is still waiting and counts the Distance from actual position to the Point.

This happens always by all tasks, which are not reqognizes as done.

Can you give me this scenario to download, this will greatly help, I have tested 3 scenarios with success. Maybe this scenario is using custom scenario markers (which are not supported yet by RWE)

You already have this Route and Szenario: Beitrag #661.

StS Oh ok One question, in the first task of this scenario do you need to pickup some coal for the steam locomotive and in the second task some water ? Is that right ?

YES, the tender end must be under the middle of the Coal- Loader, and for the Water the the tender Must be under the watercrane. allways press T for loading.

Alright so I think it explains everything. Steam locomotive are not fully supported yet by the RWE 2 simulation engine.

I tried to make a temporary fix for this and I have sent you another test file on RW Central. Pleas check it out and tell me if there is any change. Thank you !

The task will shown,

Pressed T the Red "baken" runs, F1 Shows succes, but there no tik for succes in the RWH2 List.

Well I will need to work more on steam trains then. Steam trains proper support will come in the near future. Thank you for your test and thank you for your patience

Ist not only Steam Trains, its the Task in The Szenario-Editor

For Load or unload things Like fuel, Coal, Container ... (Loading Fuel/Fright)

Attached You will find the testroute with an additional Container load and unload szenario. T load, shif+T unload.

Coaling point is now here:

Good luck to find a good solution.

oldsnake is there anywhere a Button, to say the Tool override the not done task?

Thats not a problem by Fuel/Loading tasks, when a Station Stop is accidendly not done, then it is the Problem too. RWEH2 stops working.

Zitat von StS

oldsnake is there anywhere a Button, to say the Tool override the not done task?

Thats not a problem by Fuel/Loading tasks, when a Station Stop is accidendly not done, then it is the Problem too. RWEH2 stops working.

If I understood right, tasks can be artificially completed in the Debug window, see RE: RW Enhancer 2 erschienen

However, oldsnake it would be useful to be able to override the failure of a previous task in RWE2. This still happens frequently in Quick Drive when the train is moved forward at a departure station whose position has been incorrectly detected (in these cases, I often forget to define the task as succeded before leaving). On the screenshot, I would have to move back 50 metres for RWE2 to validate the task, even though I'm at the platform where I have to pick up passengers.

oldsnake

Wenn ich ein Karriere Szenario ändere als Timetabel oder Standard Szenario ändere, weil ich mit anderen Rollmaterial fahren möchte, warum erkennt der RW2 das nicht im TS. Es kommt kein Begin Service. Somit kann ich leider das neue Hud nicht nutzen. Mach ich was falsch oder liegt der Fehler woanders. Bei Aufgabe Paketen via 3DZug oder JTG z.B. funktioniert es ja auch. Und das sind ja auch nur Timetable Szenarios. Weißt du was ich meine?

Frankengrizzly Warum willst du das Szenario von Karriere überhaupt ändern?

Das HUD (F3 oder F4) aus dem TS brauchst du ja ohnehin nicht mehr.

Gruß Mirko

Karriere ist oft im ap, da geändert oder ausgepackt und geändert?
Cache geleert?