Alles anzeigenHi,
Thanks for the new update!
There is only one, previously encountered problem.
When loading a scenario with the train in sandwichmode (both loco's at train ends), RW hangs. Only a black screen and nothing more.
With one loco in the consist or both loco's at the front, there is no problem.
Problem occurs with vR and Christrains ICRmh coaches.
Maybe you can tackle this problem again? Thanks!
Kal000px is this problem still going to be fixed? 
So I have some troubles with the ETCS markers, I want to use it on the HSL Line in Holland. I tried to follow the manual but that did not work for me.
I need to go from ATB tot ETCS L2, so which order do I need to place the markers.
I have now only the ETCS_ETCSL1 and after that ETCS_ETCSL2, but i got a emergency brake.
So who know's which markers i need to use to go from ATB to ETC L2?
Hello,
I played a few times with this train in the Netherlands and i have the following things that i want to report
The ATB system:
When the speed goes down, the ATB switches to a lower speed, and rings immediately for a few seconds. If you fast enough you can apply the brake..
In real life when the ATB switches to a lower speed, you have 3 seconds to apply the brake, if you don't then the bell rings for like 3 seconds and after that you have the emergency brake.
In version 1.04 it is: "Ting" "TRRRRRRRRRRRRR" "Emergency brake (when you not braking)", but it should be: "Ting" "3 seconds delay" "TRRRRRRRRR" "Emergency brake (when you not braking)".
This only applies when the train is going in a lower speed zone!!!
Request: Can you put a 3 second timer between the moment the ATB switches to a lower speed and the moment you apply the brake? If you want to learn something more about the ATB:
Sifa:
In the manual you can disable sifa with shift + 9, after i used that combination Sifa is still on, so i cannot disable Sifa. (You can see Sifa disabled message but the white light still pops up.)
ZWS (Loc + Coaches + Loc):
- I also noticed when i drive in ZWS and i go back to the second loc the Sifa emergency brake is applied (I don't know if this affect driving)
- The manual says to activate ZWS: After starting up batteries on both locomotives, move to the back locomotive and by pressing Shift + 7 turn on ZWS. Pull out the key from back wall. After ZWS activation move to front locomotive, turn on ZWS the same way, put in the key and activate the cabin. Back locomotive is now in slave mode and listens to orders from front locomotive
When i go to the second loc and enable ZWS it says "ZWS Enabled", I do the same in the first loc and i says "ZWS Disabled", and if I use the same combination again it says "ZWS Enabled". So do i need to do that only in the second loc? Or only in the first loc?
Voltage system:
I still have a lot of "Stürong" messages when I drive with the 1.5 kv, maybe i'm doing something wrong? I give like 36% traction and when i'm driving 80> the train gives me a "Stürong" end the HS is disabled.
Train:
After driving for a while and I let the train coast, it decreased speed very quickly, faster than in the beginning of the scenario (this applies when i drive ZWS Loc + coaches + Loc)
mixlivetobi I think you need to set the reverser in the forward position.
Kal000px Thank you for the update!!
I think the scripts Christrains ICRmh coaches are disturbing the scripts from the TRAXX loco. Maybe since the vR ZWS support? Because in v1.02 these problems were not present.
Sebastiaan I do not think the Christrains Script is a issue, because the VR coaches are also giving issues.
I will take some further investigations and fix it, thank You both very much!
Kal000px Thank you very much!
Here is the file you requested
blivius92 could You please try to reproduce it with Logmate turned on? Thanks for instructions.
Hi I missed your message completely, so what is logmate?
Ok that should be the right way. Wy the crash???
Which Szenario-Type?
Can Yo give a solo loco a player-tik?
I use a standard scenario
Solo loc does not give any problems
But let's make it more crazy
This does work
It also gives me this message
So there two locos?, Only one Player in one loco, not in the other one !
Yes, make a setup like this, again wagons does not matter, you can also use VR coaches
Assign a driver:
Again this is still fine.
Double click on the driver
Once i select that option the game crashes.
https://christrains.com/nl/ts_product_traxx186.html these coaches.
But I think it could also be something with my scenario, because it does not crache when i remove the driver from the train.
Or make a new scenario with the same setup
I know how to reproduce the problem:
Create a scenario (route does not matter)
Place 7 person coaches (does not matter which i picked 7 from Virtual Railroads)
Place 1 loc on both ends and assign a driver
Once you select this option, the game crashes.
I want to report a bug in the new 1.03 version:
I made a scenario in the Netherlands, we have the following setup: Traxx - 9 Passenger Wagons - Traxx
When i load my scenario it crashes, when i go back to version 1.02 it loads.
When i place the lok apart from the wagons the scenario doens't crash (version 1.03).
When i go back to the editor, place loc 1 against the wagons it still works, but when i link the second loc to the wagons the game crashes.
Du kannst ein MKlink machen:
mklink /J "C:\Program Files (x86)\Steam\steamapps\common\railworks" "I:\Steam\steamapps\common\RailWorks"
- mklink /J "C:\Program Files (x86)\Steam\steamapps\common\railworks" "Dein railworks Directory"
